This is the info manual for @value{PACKAGE} version @value{VERSION}, a Virtual Private Network daemon.
-Copyright @copyright{} 1998-2006 Ivo Timmermans,
+Copyright @copyright{} 1998-2008 Ivo Timmermans,
Guus Sliepen <guus@@tinc-vpn.org> and
Wessel Dankers <wsl@@tinc-vpn.org>.
@section Configuring the kernel
@menu
-* Configuration of Linux kernels 2.1.60 up to 2.4.0::
-* Configuration of Linux kernels 2.4.0 and higher::
+* Configuration of Linux kernels::
* Configuration of FreeBSD kernels::
* Configuration of OpenBSD kernels::
* Configuration of NetBSD kernels::
@c ==================================================================
-@node Configuration of Linux kernels 2.1.60 up to 2.4.0
-@subsection Configuration of Linux kernels 2.1.60 up to 2.4.0
-
-@cindex ethertap
-For kernels up to 2.4.0, you need a kernel that supports the ethertap device.
-Most distributions come with kernels that already support this.
-If not, here are the options you have to turn on when configuring a new kernel:
-
-@example
-Code maturity level options
-[*] Prompt for development and/or incomplete code/drivers
-Networking options
-[*] Kernel/User netlink socket
-<M> Netlink device emulation
-Network device support
-<M> Ethertap network tap
-@end example
-
-If you want to run more than one instance of tinc or other programs that use
-the ethertap, you have to compile the ethertap driver as a module, otherwise
-you can also choose to compile it directly into the kernel.
-
-If you decide to build any of these as dynamic kernel modules, it's a good idea
-to add these lines to @file{/etc/modules.conf}:
-
-@example
-alias char-major-36 netlink_dev
-alias tap0 ethertap
-options tap0 -o tap0 unit=0
-alias tap1 ethertap
-options tap1 -o tap1 unit=1
-...
-alias tap@emph{N} ethertap
-options tap@emph{N} -o tap@emph{N} unit=@emph{N}
-@end example
-
-Add as much alias/options lines as necessary.
-
-
-@c ==================================================================
-@node Configuration of Linux kernels 2.4.0 and higher
-@subsection Configuration of Linux kernels 2.4.0 and higher
+@node Configuration of Linux kernels
+@subsection Configuration of Linux kernels
@cindex Universal tun/tap
-For kernels 2.4.0 and higher, you need a kernel that supports the Universal tun/tap device.
+For tinc to work, you need a kernel that supports the Universal tun/tap device.
Most distributions come with kernels that already support this.
Here are the options you have to turn on when configuring a new kernel:
It's not necessary to compile this driver as a module, even if you are going to
run more than one instance of tinc.
-If you have an early 2.4 kernel, you can choose both the tun/tap driver and the
-`Ethertap network tap' device. This latter is marked obsolete, and chances are
-that it won't even function correctly anymore. Make sure you select the
-universal tun/tap driver.
-
If you decide to build the tun/tap driver as a kernel module, add these lines
to @file{/etc/modules.conf}:
For OpenBSD version 2.9 and higher,
the tun driver is included in the default kernel configuration.
There is also a kernel patch from @uref{http://diehard.n-r-g.com/stuff/openbsd/}
-which adds a tap device to OpenBSD.
-This should work with tinc.
-
+which adds a tap device to OpenBSD which should work with tinc,
+but with recent versions of OpenBSD,
+a tun device can act as a tap device by setting the link0 option with ifconfig.
@c ==================================================================
@node Configuration of NetBSD kernels
@subsection Device files
@cindex device files
-First, you'll need the special device file(s) that form the interface
-between the kernel and the daemon.
-
-The permissions for these files have to be such that only the super user
-may read/write to this file. You'd want this, because otherwise
-eavesdropping would become a bit too easy. This does, however, imply
-that you'd have to run tincd as root.
-
-If you use Linux and have a kernel version prior to 2.4.0, you have to make the
-ethertap devices:
-
-@example
-mknod -m 600 /dev/tap0 c 36 16
-mknod -m 600 /dev/tap1 c 36 17
-...
-mknod -m 600 /dev/tap@emph{N} c 36 @emph{N+16}
-@end example
+Most operating systems nowadays come with the necessary device files by default,
+or they have a mechanism to create them on demand.
-There is a maximum of 16 ethertap devices.
-
-If you use the universal tun/tap driver, you have to create the
-following device file (unless it already exist):
+If you use Linux and do not have udev installed,
+you may need to create the following device file if it does not exist:
@example
-mknod -m 600 /dev/tun c 10 200
+mknod -m 600 /dev/net/tun c 10 200
@end example
-If you use Linux, and you run the new 2.4 kernel using the devfs filesystem,
-then the tun/tap device will probably be automatically generated as
-@file{/dev/net/tun}.
-
-Unlike the ethertap device, you do not need multiple device files if
-you are planning to run multiple tinc daemons.
-
@c ==================================================================
@node Other files
Note that you can only use one device per daemon.
See also @ref{Device files}.
+@cindex DeviceType
+@item DeviceType = <tun|tunnohead|tunifhead|tap> (only supported on BSD platforms)
+The type of the virtual network device.
+Tinc will normally automatically select the right type, and this option should not be used.
+However, in case tinc does not seem to correctly interpret packets received from the virtual network device,
+using this option might help.
+
+@table @asis
+@item tun
+Set type to tun.
+Depending on the platform, this can either be with or without an address family header (see below).
+
+@cindex tunnohead
+@item tunnohead
+Set type to tun without an address family header.
+Tinc will expect packets read from the virtual network device to start with an IP header.
+On some platforms IPv6 packets cannot be read from or written to the device in this mode.
+
+@cindex tunifhead
+@item tunifhead
+Set type to tun with an address family header.
+Tinc will expect packets read from the virtual network device
+to start with a four byte header containing the address family,
+followed by an IP header.
+This mode should support both IPv4 and IPv6 packets.
+
+@item tap
+Set type to tap.
+Tinc will expect packets read from the virtual network device
+to start with an Ethernet header.
+@end table
+
@cindex GraphDumpFile
@item GraphDumpFile = <@var{filename}> [experimental]
If this option is present,
@cindex Name
@item Name = <@var{name}> [required]
-This is a symbolic name for this connection. It can be anything
+This is a symbolic name for this connection.
+The name should consist only of alfanumeric and underscore characters (a-z, A-Z, 0-9 and _).
@cindex PingInterval
@item PingInterval = <@var{seconds}> (60)
Can be anything from 0
up to the length of the digest produced by the digest algorithm.
+@cindex PMTU
+@item PMTU = <@var{mtu}> (1514)
+This option controls the initial path MTU to this node.
+
+@cindex PMTUDiscovery
+@item PMTUDiscovery = <yes|no> (yes)
+When this option is enabled, tinc will try to discover the path MTU to this node.
+After the path MTU has been discovered, it will be enforced on the VPN.
+
@cindex Port
@item Port = <@var{port}> (655)
This is the port this tinc daemon listens on.
@uref{ftp://ftp.isi.edu/in-notes/rfc1519.txt, RFC1519}
@cindex TCPonly
-@item TCPonly = <yes|no> (no) [experimental]
+@item TCPonly = <yes|no> (no)
If this variable is set to yes, then the packets are tunnelled over a
TCP connection instead of a UDP connection. This is especially useful
for those who want to run a tinc daemon from behind a masquerading
projects / tinc / commitdiff